Product description
Crystal clear, fast, two-part epoxy adhesive.

Field of application
Ideal for fast, strong and invisible repairing of pottery, porcelain, glass, leather, wood, stone, metal and ceramics to themselves or to each other. Ideal for filling cracks thanks to filling capacity. Not suitable for Polyethylene (PE), polypropylene (PP), P.T.F.E. and silicone rubber.

Properties

• Fast
• Crystal clear
• Super strong
• Universal
• Suitable for numerous materials
• Temperature resistant from -40°C to +100°C
• Gap-filling
• Waterproof
• Chemicals resistant
• Paintable

Preparation
Working conditions: Only use at temperatures between +5°C and +35°C. Product cures after mixing resin and hardener.
Personal safety: Preferably wear gloves during use.
Surface requirements: Materials to be bonded should be dry, clean and free of grease.
Preliminary surface treatment:Degrease parts to be bonded with Bison Thinner for Bison Kit or acetone. Roughen up smooth materials (sand paper).
Tools: Mix and apply with plastic spatula. Clean tools with warm water and soap directly after use.

Application
Mixture ratio: 1:1
Coverage: 24 ml = approx. 240cm² (coat of 1mm)
Directions for use:
Remove spatula from side of double syringe and cap from handle. Break safety seal of double syringe. Dispense equal quantities of both parts into enclosed mixing tray. Stir well using enclosed spatula. At room temperature (+20°C), mixture remains workable for approx. 5 minutes. Apply a thin layer to one side. Join immediately and hold in place for 20 minutes. Do not move bonded parts until after complete cure. After use, clean nozzles with a cloth and place special double cap from handle on double syringe. Do not mix resin and hardener unless for bonding.
Potlife: 5 minutes
Stains/residue: Remove fresh stains immediately with warm water and soap. Cured adhesive residue can only be removed mechanically.

Cure times
Handling time: approx. 20 minutes
Dry/Cure time: approx. 1hour. Curing takes longer at lower temperatures, and shorter at higher temperatures.

Technical properties
Moisture resistance: Good
Water resistance: Good
Temperature resistance: -40°C to +100°C
Chemicals resistance: Good
Filling capacity: Good
Technical specifications
Chemical base: Resin: epoxy resin. Hardener: modified amide
Colour: Transparent
Viscosity: Liquid
Solid contents: approx. 100 %
Density: approx. 1.16 g/cm³
Storage conditions
At least 24 months after date of manufacture. Limited shelf life after opening. Store in a dry, cool and frost-free place.

High quality, strong glue for plastics.

Product description
High quality and strong glue for repairing many plastic(household) objects.

Field of application
Glues household synthetics such as ABS, acrylic glass polycarbonate and rigid PVC. Excellent for repairing plastic household appliances such as: (mobile) phone, coffee-maker, audio appliances, water boilers, remote control, computer, printer, keyboard. Also excellent for fixing pvc electrical tubes and plastic bicycle and car light parts. Not suitable for Polyethylene (PE), Polypropylene (PP) and P.T.F.E.

Properties

• Strong
• Waterproof
• Temperature resistant up to + 100°C
• Transparent
• Preparation

Preparation
Working conditions: Do not use at temperatures below +5°C.
Surface requirements: Materials to be glued should be clean, dry, and free of dust and grease.
Preliminary surface treatment: If necessary degrease with acetone.

Application
Directions for use:
Apply glue thinly to one side. Join immediately and press firmly on entire surface.
Stains/residue: Remove fresh stains immediately with acetone. Dried glue residue can only be removed mechanically.
Cure times
Handling time: approx. 3 hours.
Dry/Cure time: approx. 24 hours.
Dry/Cure time: approx. 24 hours.

Technical properties
Temperature resistance: Up to +100°C.
Chemicals resistance: Resistant to household cleaning products.
Technical specifications
Chemical base: PVC copolymer
Color: Transparent
Viscosity: Runny
Solid contents: approx. 25 %

Storage conditions
At least 24 months after date of manufacture. Limited shelf life after opening. Store in a dry, cool and frost-free place.

Metal colored, hard wearing, two-part epoxy adhesive

Product description
Metal coloured, hardwearing, two-part epoxy adhesive.

Field of application
Ideal for hardwearing repairs to metal objects which need to resist extreme conditions (forces, vibrations, (sea) water, heavy strains), such as tools or parts of a car, motorcycle, bicyle or moped, metal (garden) fences or cutlery. Also suitable for filling small holes in radiators. Bonds metal (steel, aluminium, iron) parts amongst themselves or to stone, wood, concrete and various synthetics (such as Formica, polyester and bakelite). Not suitable for Polyethylene (PE), Polypropylene (PP), P.T.F.E. and silicone rubber.

Properties

• Hardwearing
• Metal coloured
• Resistant to extreme conditions
• Temperature resistant from -40°C to +60°C
• Filling
• (Sea)water resistant
• High resistance to chemicals
• Can be sanded, filed, drilled and painted after curing

Preparation
Working conditions: Use only at temperatures between +5°C and +35°C. Product cures after mixing resin and hardener.
Personal safety: Preferably wear gloves during use.
Surface requirements: Materials to be bonded should be dry, clean and free of grease.
Preliminary surface treatment:Degrease parts to be bonded with Bison Thinner for Bison Kit or acetone. Roughen up smooth materials (sand paper).
Tools: Mix and apply with plastic spatula. Clean tools with warm water and soap directly after use.

Application
Mixture ratio: 1:1
Coverage: 24 ml = approx. 240cm² (coat of 1mm)

Directions for use:
Remove spatula from side of double syringe and cap from handle. Break safety seal of double syringe. Dispense equal quantities of both parts into enclosed mixing tray. Stir well using enclosed spatula until mixture has a uniform colour. At room temperature (+20°C), mixture remains workable for approx. 45 minutes. Apply a thin layer to one surface. Join immediately and hold in place for 10 hours. Do not move bonded parts until after complete cure. After use, clean nozzles with a cloth and place special double cap from handle on double syringe. Do not mix resin and hardener unless for bonding.

Potlife: 45 minutes
Stains/residue: Remove fresh stains immediately with warm water and soap. Cured adhesive residue can only be removed mechanically.

Cure times
Handling time: approx. 10 hours
Dry/Cure time: approx. 24 hours. Curing takes longer at lower temperatures, and shorter at higher temperatures.

Technical properties
Moisture resistance: Good
Temperature resistance: -40°C to +60°C
Chemicals resistance: Very Good
Paintability: Good
Filling capacity: Good
Technical specifications
Chemical base: Resin: epoxy resin. Hardener: modified amide
Colour: Grey
Viscosity: Pasty
Solid contents: approx. 100 %
Density: approx. 1.2 g/cm³

Storage conditions
At least 24 months after date of manufacture. Limited shelf life after opening. Store in a dry, cool and frost-free place.

Universal, strong, two-part epoxy adhesive

Product description
Universal, strong, two-part epoxy adhesive.

Field of application
Ideal for repairs to metals, pottery, porcelain, crystal, glass, ivory, pearls, precious stones and numerous synthetics (such as polyester, bakelite, Formica, rigid polystyrene and acrylic glass.Not suitable for Polyethylene (PE), Polypropylene (PP), P.T.F.E. and silicone rubber.

Properties

• Strong
• Temperature resistant from -20°C to +60°C
• Filling
• Water resistant
• Chemicals resistant
• Paintable

Preparation
Working conditions: Use only at temperatures between 5°C and +35°C. Product cures after mixing resin and hardener.
Personal safety: Preferably wear gloves during use.
Surface requirements: Materials to be bonded should be dry, clean and free of grease.
Preliminary surface treatment:Degrease parts to be bonded with Bison Thinner for Bison Kit or acetone. Roughen up smooth materials (sand paper).
Tools: Mix and apply with plastic spatula. Clean tools with warm water and soap directly after use.

Application
Mixture ratio: 1:1
Coverage: 24 ml = approx. 240cm² (coat of 1mm)

Directions for use:
Remove spatula from side of double syringe and cap from handle. Break safety seal of double syringe. Dispense equal quantities of both parts into enclosed mixing tray. Stir well using enclosed spatula until mixture has a uniform colour. At room temperature (+20°C), mixture remains workable for approx. 1,5 hours. Apply a thin layer to one surface. Join immediately and hold in place for 7 hours. Do not move bonded parts until after complete cure. After use, clean nozzles with a cloth and place special double cap from handle on double syringe. Do not mix resin and hardener unless for bonding.

Potlife: 1,5 hours.
Stains/residue: Remove fresh stains immediately with warm water and soap. Cured adhesive residue can only be removed mechanically.
Cure times
Handling time: approx. 7 hours.
Dry/Cure time: approx. 24 hours. Curing takes longer at lower temperatures, and shorter at higher temperatures

Technical Properties
Moisture resistance: Good
Temperature resistance: -20°C to + 60°C
Chemicals resistance: Good
Paintability: Good
Filling capacity: Good

Technical specifications
Chemical base: Resin: epoxy resin. Hardener: modified amide
Colour: Light yellow
Viscosity: Liquid
Solid contents: approx. 100 %
Density: approx. 1.15 g/cm³

Storage conditions
At least 24 months after date of manufacture. Limited shelf life after opening. Store in a dry, cool and frost-free place.

Tear-off card with 12 tubes of universal super glue.

Product description
Super strong, fast, correctable and slightly filling super glue in the form of a gel. Ideal for porous materials.

Field of application
Glues various materials, such as earthenware, porcelain, cork, wood, cardboard, metal, rubber and many synthetics. Not suitable for Not suitable for some synthetics (PE, PP, PTFE and silicone rubber) and car windows.

Properties

• Does not drip or run down vertical surfaces
• Briefly correctable
• Slightly filling (also suitable for less well-fitting parts)
• Ideal for porous materials
• Super strong
• Fast

Preparation
Working conditions: Do not use at temperatures below +10°C.
Surface requirements: Materials to be fastened should be clean, dry, free of dust and grease and well-fitting.
Preliminary surface treatment:Degrease with acetone or Bison Thinner. Pretreat acid reacting surfaces (such as aluminium) with diluted ammonia, then rinse with water and wipe dry. Slightly roughen metals.
Tools: Work directly from the tube, using the very fine dispenser nozzle.

Application
Coverage: One drop covers approx. 2 cm² of surface to be glued. Only for spot bonding.

Directions for use:
Activate tube by turning cap. Do not push in tube while piercing. Do not open with scissors or knife. Apply glue as thinly as possible (less than one drop) on one side (too much glue slows down curing process significantly!). Nozzle should touch surface while applying glue. Immediately join parts and and press for a short time (10-60 seconds) to allow glue to spread evenly over surfaces. Manual pressure will do. When glueing metal, curing time can be shortened by, before joining, briefly breathing on side where glue is applied. After use, clean nozzle with a dry cloth and close tube by screwing black cap back on. Expose glue to air as little as possible.
Stains/residue: Wipe off excess glue immediately with a dry cloth. After curing, glue residue is very difficult to remove. Acetone will dissolve glue (but very slowly).
Points of attention: Attention: Super glue contains cyanoacrylate. Dangerous: will stick together skin and eyelids within seconds. Keep out of reach of children. In case of contact with skin, do not try to remove glue by force. In such cases, glue will automatically be rejected by skin. Then wash skin with water. In case of contact with eyes, keep eyelids open, rinse immediately with water and seek medical attention. Separate glued fingers by soaking them well in water and rolling a pencil between them.

Cure times
Handling time: approx. 15 seconds to 2 minutes, depending on nature of materials to be bonded. After 2-10 minutes glue joint is strong enough to be handled.
Full bond strength: Full bond strength after approx. 24 hours.

Technical properties
Moisture resistance: Good
Temperature resistance: -40°C to +80°C
Chemicals resistance: Good
Filling capacity: Good
Technical specifications
Chemical base: Cyanoacrylate
Color: Transparent
Viscosity: Liquid
Solid contents: approx. 100 %
Density: approx. 1.06 g/cm³

Storage conditions
At least 24 months after date of manufacture. Limited shelf life after opening. Store in a dry, cool, frost-free place. Storage below +5°C (in refrigerator) ensures maximum shelf life.

Professional super glue in handy dispenser bottle.

Product description
Super strong, very fast, professional super glue in handy dispenser bottle.

Field of application
Glues various materials, such as most synthetics, metal, rubber, porcelain, wood and cork. Not suitable for earthenware, several synthetics (PE, PP, PTFE and silicones) and car windows.

Properties

• Industrial quality.
• In handy dispenser bottle
• Super strong
• Very fast
• Clear

Preparation
Working conditions: Do not use at temperatures below +10°C.
Surface requirements: Materials to be fastened should be clean, dry, free of dust and grease and well-fitting.
Preliminary surface treatment:Degrease with acetone or Bison Thinner. Pretreat acid reacting surfaces (such as aluminium) with diluted ammonia, then rinse with water and wipe dry. Slightly roughen metals.
Tools: Work directly from the bottle, using the very fine dispenser nozzle.

Application
Coverage: One drop covers approx. 2 cm² of surface to be glued. Only for spot bonding.

Directions for use:
Open bottle by pressing and turning cap at the same time. Apply glue as thinly as possible on one side (too much glue slows down curing process significantly!). Immediately join parts and press for a short time (10-60 seconds) to allow glue to spread evenly over surfaces. Manual pressure will do. The connection can be reinforced by dripping some extra glue into the joint. When glueing metal, curing time can be shortened by, before joining, briefly breathing on side where glue is applied. Clean nozzle with dry cloth immediately after use. Then close bottle by replacing cap. Expose glue to air as little as possible.

Stains/residue: Wipe off excess glue immediately with a dry cloth. After curing, glue residue is very difficult to remove. Acetone will dissolve glue (but very slowly).

Points of attention: Attention: Super glue contains cyanoacrylate. Dangerous: will stick together skin and eyelids within seconds. Keep out of reach of children. In case of contact with skin, do not try to remove glue by force. In such cases, glue will automatically be rejected by skin. Then wash skin with water. In case of contact with eyes, keep eyelids open, rinse immediately with water and seek medical attention. Separate glued fingers by soaking them well in water and rolling a pencil between them.

Cure times
Handling time: approx. 10 seconds to 1minute, depending on nature of materials to be bonded. After 2-5 minutes glue joint is strong enough to be handled.
Full bond strength: Full bond strength after approx. 24 hours

Technical properties
Moisture resistance: Good
Temperature resistance: -40°C to +80°C
Chemicals resistance: Good
Filling capacity: Limited
Technical specifications
Chemical base: Cyanoacrylate
Color: Transparent
Viscosity: Runny
Solid contents: approx. 100 %
Density: approx. 1.06 g/cm³

Storage conditions
At least 18 months after date of manufacture. Limited shelf life after opening. Store in a dry, cool, frost-free place. Storage below +5°C (in refrigerator) ensures maximum shelf life.

Tear-off card with 12 tubes of universal super glue.

Product description
Super strong, very fast, universal super glue.
Field of application
Glues various materials, such as many synthetics, metal, rubber, porcelain, wood and cork. Not suitable for earthenware, several synthetics (PE, PP, PTFE and silicone rubber) and car windows.

Properties

• Super strong
• Very fast

Preparation
Working conditions: Do not use at temperatures below +10°C.
Surface requirements: Materials to be fastened should be clean, dry, free of dust and grease and well-fitting.
Preliminary surface treatment:Degrease with acetone or Bison Thinner. Pretreat acid reacting surfaces (such as aluminium) with diluted ammonia, then rinse with water and wipe dry. Slightly roughen metals.
Tools: Work directly from the tube, using the very fine dispenser nozzle.

Application
Coverage: One drop covers approx. 2 cm² of surface to be glued.

Directions for use:
Activate tube by turning cap. Do not push in tube while piercing. Do not open with scissors or knife. Screw white cap on opened tube. Apply glue as thinly as possible (less than one drop) on one side (too much glue slows down curing process significantly!). Nozzle should touch surface while applying glue. Immediately join parts and and press for a short time (10-60 seconds) to allow glue to spread evenly over surfaces. Manual pressure will do. The connection can be reinforced by dripping some extra glue into the joint. When glueing metal, curing time can be shortened by, before joining, briefly breathing on side where glue is applied. After use, clean nozzle with a dry cloth and close tube by screwing black cap back on. Expose glue to air as little as possible.
Stains/residue: Wipe off excess glue immediately with a dry cloth. After curing, glue residue is very difficult to remove. Acetone will dissolve glue (but very slowly).
Points of attention: Attention:Super glue contains cyanoacrylate. Dangerous: will stick together skin and eyelids within seconds. Keep out of reach of children. In case of contact with skin, do not try to remove glue by force. In such cases, glue will automatically be rejected by skin. Then wash skin with water. In case of contact with eyes, keep eyelids open, rinse immediately with water and seek medical attention. Separate glued fingers by soaking them well in water and rolling a pencil between them.

Cure times
Handling time: approx. 10 seconds to 1minute, depending on nature of materials to be bonded. After 2-5 minutes glue joint is strong enough to be handled.
Full bond strength: Full bond strength after approx. 24 hours

Technical properties
Moisture resistance: Good
Temperature resistance: -40°C to +80°C
Chemicals resistance: Good
Filling capacity: Limited
Technical specifications
Chemical base: Cyanoacrylate
Color: Transparent
Viscosity: Runny
Solid contents: approx. 100 %
Density: approx. 1.08 g/cm³

Storage conditions
At least 24 months after date of manufacture. Limited shelf life after opening. Store in a dry, cool, frost-free place. Storage below +5°C (in refrigerator) ensures maximum shelf life.