High-quality one-component polyurethane fireproof foam. It has excellent thermal and sound insulation properties and excellent bonding strength. Homogeneous structure of the product provides excellent adhesion to the work surface.

Compliance with fire safety.
High thermal stability.
LOW-EXPANSION.

SCOPE:

Perfect for designs with a high fire resistance class. Used for mounting doors and windows fixing wall panels, roof tiles, insulation fixing tube filling holes and gaps as well as thermal insulation. Good adhesion to many construction materials, except Teflon, polyethylene and silicone surfaces.

APPLICATION

Before use, the foam cylinder temperature should be about 20°C. Heating cylinder is permitted in a container of warm water (up to +30°C). Vigorously shake the bottle for 30 seconds. Place the cylinder valve is facing up. Screw mounting part of the gun on to threaded portion of the adapter. Make sure the connection is secure. Place the can upside down. Start using the product. If necessary, repeat shaking.

IMPORTANT:

Before using the foam need to clean work surfaces from dust, ice, grease, and other contaminants, and moisten with water. Fresh dirt foam as well as the cured foam can be removed with acetone or TRITOSIL® Cleaner, or by mechanical ways. Cured foam can be painted.

INGREDIENTS: diphenylmethane diisocyanate (isomers and homologues) (CAS 9016-87-9), propane / butane / izobugan (CAS 74-98-6 (CAS: 106-97-8) / CAS 75-28-5). R20 Harmful by inhalation. RZ6 / 37/38 Irritating eyes, respiratory system and skin. R40 Limited confirmed carcinogenic effect. R42 / 43 Inhalation and skin contact can lead to allergies. R48 / 20 Harmful: Prolonged exposure through inhalation and ingestion of the risk of serious injury. S23 Do not breathe vapors. S36 / 37/39 Use personal protective equipment. Protect your face and eyes. S45 In case of accident or if you feel unwell, seek medical advice immediately and show this container or label. 851 Use only in well-ventilated areas. S63 In case of accidental inhalation, breathe in fresh air and keep quiet. Contains isocyanates. See information supplied by the manufacturer. Container is under pressure. Keep it away from direct sunlight, heat above 50°C. Do not pierce or burn even after use. Do not spray on a naked flame or any hot surfaces. Keep out of the reach of children. Keep away from sources of fire or smoke. Individuals who are sensitive to isocyanate may have allergic reactions when using this product. People suffering from asthma, eczema or having skin problems should avoid contact with this product. This product should not be used under conditions of poor ventilation without a mask with an attached gas filter (ie type A1 according to standard EN 14387).

SPECIFICATIONS

Fire resistance: up to 240 minutes.
Application temperature: +5°C to +30°C
Can temperature when using: + 10°C to + 25°C

Surface drying time: 10-16 minutes. Cured foam can be painted and machined 30-40 minutes after completion of the work at the ambient temperature of + 23 ° C and 50% relative humidity. After complete curing (24 hours) the foam must be protected from exposure to ultraviolet rays. Operating temperature: -50 ° C to + 90 ° C (for short periods of -65 ° C to + 130 ° C).

STORAGE

Stored and transported in an upright position. Store in a dry and ventilated place at temperatures between + °C to +30°C. Permitted to store or transport cylinders at -25 ° C for 25 days. Do not store near sources of heat, exposed to direct sunlight and mechanical stress, which can lead to damage and depressurization cylinders. Shelf life 12 months.

SAFETY:

R20 Harmful by inhalation. R36 / 37/38 Irritating eyes, respiratory system and skin. R41 there is a risk of serious damage to eyes. R42 / 43 Inhalation and skin contact can lead to allergies. S16 Keep away from sources of ignition and do not smoke. S23 Do not breathe vapors. S26 In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. S36 / 37/39 Use personal protective equipment. S46 If swallowed, seek medical advice and show the bottle and label. S51 Use only in well-ventilated areas S63 In case of inhalation, need to breathe in fresh air. Contains isocyanates, see information supplied by the manufacturer. Cylinder is pressurized; storage temperature should not exceed 50°C. Do not pierce or burn even after use. Keep out of the reach of children. Dispose of in accordance with local regulations.

APPLICATION:

PU Foam is designed for installation of windows and doors, filling gaps, thermal and acoustic insulation, and sealing compounds in the frame construction, as well as other construction and installation works.

Capacity: 65 liters
Volume increment (secondary expansion): 70-100%
Processing time: 40 minutes
Application temperature: -5°C to + 30°C
Can temperature: + 15°C to + 30°C
Water absorption (after 24 hours): 2.5%
High thermal and acoustic insulation level
Resistance to moisture and mildew
Shelf life: 12 months

All parameters are measured in accordance with international standards and are highly dependent on external conditions (can temperature, air and surface quality of the equipment used, the air pressure, qualification of users).

DIRECTIONS FOR USE:

Always use mechanical fasteners when installing windows and doors. Clean, degrease and moisten the surface with water. Shake can well and attach to a gun adapter. Hold the can upside down during use. Fill the gaps and joints up to 60% of depth (foam increases in volume). When the foam is fully cured it can be protected from UV by using a sealant, plaster or paint over it (not earlier than 24 hours after application). Fresh dirty foam as well as the cured foam can be removed with acetone or TRITOSIL® Cleaner, or by mechanical way. Cured foam can be painted.

INGREDIENTS : 4,4 – diphenyl methane diisocyanate (EC ? 202-966-0); propane (EC ? 200-827-9V), butane (EC ? 203-448-7V), isobutane (EC ? 200-857-2).

SAFETY: R20 Harmful by inhalation. R36 / 37/38 Irritating eyes, respiratory system and skin. R41 there is a risk of serious damage to eyes. R42 / 43 Inhalation and skin contact can lead to allergies. S16 Keep away from sources of ignition and do not smoke. S23 Do not breathe vapors. S26 In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. S36 / 37/39 Use personal protective equipment. S46 If swallowed, seek medical advice and show the bottle and label. S51 Use only in well-ventilated areas S63 In case of inhalation, need to breathe in fresh air. Contains isocyanates, see information supplied by the manufacturer. Cylinder is pressurized; storage temperature should not exceed 50°C. Do not pierce or burn even after use. Keep out of the reach of children. Dispose of in accordance with local regulations.

APPLICATION:

Professional foam designed for installation of windows and doors, filling gaps, thermal and acoustic insulation, and sealing compounds in the frame construction, as well as other construction and installation works.

Capacity: 45 liters
Volume increment (secondary expansion): 70-100%
Processing time: 40 minutes
Application temperature: -10°C to + 30°C
Can temperature of 15°C to + 30°C
Water absorption (after 24 hours): 2.5%
High level of thermal and acoustic insulation
Resistance to moisture and mildew
Shelf life: 12 months

All parameters are measured in accordance with international standards and are highly dependent on external conditions (can temperature, air and surface quality of the equipment used, the air pressure, the qualification of users).

DIRECTIONS FOR USE:

Always use mechanical fasteners when installing windows and doors. Clean, degrease and moisten the surface with water. Shake can well and attach to a gun adapter. Hold the can upside down during use. Fill the gaps and joints up to 60% of depth (foam increases in volume). When the foam is fully cured it can be protected from UV by using a sealant, plaster or paint over it (not earlier than 24 hours after application). Fresh dirty foam as well as the cured foam can be removed with acetone or TRITOSIL® Cleaner, or by mechanical way. Cured foam can be painted.

INGREDIENTS: 4,4 – diphenyl methane diisocyanate (EC ? 202-966-0); propane (EC ? 200-827-9V), butane (EC ? 203-448-7V), isobutane (EC ? 200-857-2).

SAFETY: R20 Harmful by inhalation. R36 / 37/38 Irritating eyes, respiratory system and skin. R41 there is a risk of serious damage to eyes. R42 / 43 Inhalation and skin contact can lead to allergies. S16 Keep away from sources of ignition and do not smoke. S23 Do not breathe vapors. S26 In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. S36 / 37/39 Use personal protective equipment. S46 If swallowed, seek medical advice and show the bottle and label. S51 Use only in well-ventilated areas S63 In case of inhalation, need to breathe in fresh air. Contains isocyanates, see information supplied by the manufacturer. Cylinder is pressurized; storage temperature should not exceed 50°C. Do not pierce or burn even after use. Keep out of the reach of children. Dispose of in accordance with local regulations.